where is the center point of ADIS16448/PCBZ ?
hi i need to connect my ADIS16448/PCBZ to my PCB. but i've been asked to know the center point of it. i've searched the datasheetbut i couldn't find it. can u help me with this?
View ArticleADIS16480 Euler accuracy/delay time
Hello,My application requires very accurate and with the smallest delay (fast response time) in measuring Pitch (and later Yaw).So After checking past forums and some experimenting, I started with the...
View ArticleHaving a problam w/ ADIS16488 SPI Communication.
Hi alli'm using the ADIS16488 and connected it with a TI DSP (delfino) through the SPI.while i'm running my code and sending addresses to the ADIS i'm getting right data (like PROD_ID etc..) but this...
View ArticleAbout vibration measurement & ADIS16006
Hello,everyone: we are working on a vibration measurement project for oil tank of transformer. Our main parameters show as following: Sensor type:MEMS; BW: 2kHz or more;...
View ArticleADXL345 and the MSP430F2013 I2C communication problem
I have set up an MSP430F2013 as the master and the ADXL345 as the slave. I am following the standard setup using the Device ID address of 0x1D. My scenario is thisGenerate a start on the I2C busSend...
View ArticleADXL375, no reading beyond +/-32G
Hello, I'm working on a project that uses the ADXL375 (+/-200G, digital output). The problem I'm having is that the accelerometer output never exceeds +/-32G. Two different reference accelerometers...
View ArticleADXL362 Interrupt questions and weird behaviour
Using the EVAL-ADXL362ZHi, I try to reliably detect an inactivity and activity on INT1. It seems to work OK, but then something weird happens. Inactive is triggered again, and again forever. It times...
View ArticleADIS16488 long-lasting performance
Hello Our company uses ADIS16488 for several years now. A couple years ago I was informed at this forum that the sensors may change their performance with time, more precisely th scale gains for gyros...
View ArticleClik here to view.
Connecting an MSP430F5438 to an ADXL346 via SPI
Hi, I've been learning for the last while about SPI and how to implement it using the MSP430F5438 Microprocessor. I've came to the point where I've taken a SPI small demo application, and have changed...
View ArticleADIS 16488 changes with time
Hi, We use ADIS16488 in our stabilization projects and we noticed that after some time (approx. 7-8 months of non daily usage) stabilization parameters of our system get worse, than they were after...
View ArticleADIS16080 output data rate?
Dear all, May I ask a question about output data rate for ADIS16080 ? Because datasheet has no description.But some Gyro MEMS datasheets describe Output Data Rate(ODR) parameter. Best Regards,Lishen
View Articleevaluate ADIS164007
can i evaluate ADIS164007 with ADIS164007 and ADISUSBZ? there are any software to evaluateADIS164007?
View ArticleADIS16485 driver for Windows
I had to convert all of my codes and software from Linux to Windows . Is there any SDK for windows? How I can read its USB port? Thank you,Siavash.
View ArticleADIS16488 Sample Rate Setting
Thanks NevadaMark.BTW, in my SPI connection with 16488, I wrote a sample rate register and set it at 10Hz. However, I would only have 4 to 5 Hz as seen from the output on the terminal. I wonder why and...
View ArticleADIS16334 old evaluation board
Hi I would like to use old ADIS16334 software.Please support me. I have ADISUSBZ and ADIS16334. (USB is typ-B)I installed new SDPDDrivers_2.exe and IMU_6DOF_3.Then it doesn't work. It should be an old...
View ArticleADIS16480 and Evaluation Board Questions
(Background:) I (or more specifically my team) recently bought the ADIS16480 and the corresponding evaluation board for use with the BeagleBone Black. This board boots from a microSD card with an...
View ArticleExcat location of accelerometer(s) in ADIS16448
Hi,I work as part of a team of engineers on visual/inertial navigation, where we try to improve our inter-sensor calibration. To verify our results, sub-millimeter accurate knowledge of the position of...
View ArticleChallenge in writing to ADIS16448 Registers
Firstly, many thanks for you detailed reply.When ADIS16448 is powered and keep the default setting unchanged, the values that i read from SMPL_PRD and SENS_AVG are 0x0B01 and 0x0402.I restore SMPL_PRD...
View Articlegetting consistent output from ADIS 16375
Hi,I am trying to get data reading from ADIS 16375 through SPI and I was able to detect output (product ID) only once on scope. I have verified that SPI signals from microcontroller are right. I am...
View ArticleClik here to view.
How to make IMU sensors insusceptible to surrounding electronics?
Hi, I am using two IMU sensors to perform the same tests and they are: ADIS16360 and ADIS16362. I attached my IMU sensor on a robot arm to take some data and the gyroscope measurements were always out...
View Article
