ADXL001 - Calibration
Hi, In a design, I need to integrate a calibrated ADXL001-500 sensor for my customer.1) Is it possible to buy an ADXL001-500 sensor and to receive a frequency response calibration for this sensor (from...
View ArticleClik here to view.
Not getting data rates 800,1600 and 3200 HZ : ADXL345
Hi,For my project my ADXL345 has to operate at all frequencies starting from 1Hz to 3200HZ.All could see all data rates from 1HZ to 400HZ,unfortunately not 800,1600 and 3200HZ.Initially i wrote 0x04 to...
View ArticleADXL345
Hi I have an ADXL345 accelerometer and need to change the range to +/- 16g. I have downloaded the ARMSWD program and KEIL and the 'sample project' however so far I can't change the range. In the...
View ArticleADXL345 output variation vs sample rate?
The output varies across different sample rates. No filter rates or any other parameters are changed between the two data sets and INT_1 is used to signal data ready. Below are 8 sequential reads from...
View ArticleAlternatives to interrupts for reading ADIS ?
Dear All, I have been successfully using my ADIS-16480 by triggering my ADIS readings with the ADIS' DIO2 pin. When the DIO2 pin transitions to a high state, it triggers an interrupt into my...
View ArticleChanging ADXL362 supply voltage in Wake-up mode
Hi I have done a design using ADXL362 and need to configure it for Wake-up detection. I have configured the activity and inactivity thresholds in referenced mode. The supply voltage changes when it is...
View ArticleClik here to view.
ADIS16480 Position tracking Problem
I am trying to track the position of the ADIS16480 sensor by double integrating the accelerometer values. The ADIS16480 is meant to run in inertial frame so that the position is output in reference to...
View ArticleADXL312 noise
We have some questions.It is helpful if you answer them. #1 Noise performance on the datasheet P3Is it same as op amp to consider the noise performance? #2 Theory on the datasheet P10It is hard to...
View ArticleADXL350
Hi,I'm using a ADXL350 in my design to detect the motion of my hardware. I have some trouble to understand how to set up the OFFSET for the three axis. I understood I should read the output for X Y and...
View ArticleClik here to view.
adis 16364 gyro read problem
hello,i have an adis 16364 imu.when i write 0x3E00. i readC7 CF 9F FF 9F FF 9F FF 9F FF 8B E8 82 E1 82 EC 82 F0 83 27 8F FFC7 C7 9F FF 9F FF 9F FF 9F FF 8A 52 82 F8 82 E3 82 E7 83 1D 8F FFC7 CC 9F FF...
View ArticleClik here to view.
ADXL345 in SPI getting wrong device ID and wrong output, working fine with I2C
Hi everyone,For my thesis project I'm using ADXL345 with nucleo-L053R8 board. Initially i connected in I2C and it is working fine. Later on i needed high datarates and switched to SPI. Unfortunately...
View ArticleClik here to view.
ADIS16488A SPI Communication Troubles
Hey everybody, first post here, so let me know if I leave out some vital information. I work in a lab at a school, and we have been trying to read data from our ADIS16488A IMU with a Beaglebone Black's...
View ArticleI am having Z-axis issues with the ADXL345 which seems to be related to...
I have several ADXL345 parts that weren't reading high enough in the z-axis. After re-soldering or replacing the part, the z-axis reading improved enough to pass my test limits. I am curious if it...
View ArticleADXL375 saturating at 25g
I am noticing that the ADXL375 device in my design is saturating at 25g when I set the bandwidth at 3200 hz. Same applies to lower data rates as well.I am reading the values in bypass mode.Any help is...
View ArticleConfusion about the ADXRS453's output
Hello,I'm now using ADXRS453 gyros. There's one problem that confuses me. In the datasheet, it is said that the rate output is SPI digital output with 16-bit data-word, and the meaningful range is...
View Articlemodel selection,configuration with triaxial MEMS Accelerometers and...
model selection,configuration with triaxial MEMS Accelerometers and single-axis Gyroscope(if do not have this,just triaxial MEMS Accelerometers with high zero offset is OK),and the zero offset of the...
View ArticleADXL362 Activity Interrupt Sensitivity
I'm trying to make the "wake up" more sensitive. It's going to sleep just fine, but it takes more motion to wake it up, and to stay awake, than I want. I've read this part of the Data Sheet about a...
View ArticleADIS16209 - Acceleration Clipping Y axis only
Hi, Ive got an ADIS16209 currently prototyped using the eval board and wired to an atmega328p. when I slide the device quickly along a bench as to keep the inclination level i can see the X axis...
View ArticleADXL362Z DB Device ID
Hello All,I am starting with ADXL362Z DB sensor, My initial step is just to read Device information. I am getting Device ID information as (0xAC) but in data sheet it is mentioned as (0xAD). Clarify...
View ArticleADXL362 Fifo Trigger Mode
Hi, I have a quick question. How would I find out when fifo got enough new data after a Trigger FIFO event occurred? I would like to sample 2s prior and after an threshold interrupt. My...
View Article
