Clik here to view.
EVAL-ADXL001
Hello everyone, I have built a testing setup that uses EVAL-ADXL001 as a calibration for the acceleration applied. A general view of the setup is shown in the figure below. Basically it is...
View ArticleADXL362 interrupts
I am using the ADXL362 with an ATTINY85 I want to run the script for a certain period then a) put the ADXL362 into wakeup mode and next b) put the ATTINY85 into power down sleep mode.I would then like...
View ArticleADIS16480 Yaw angle drifts
Hi, I am trying to use ADIS16480 . Only yaw angle which is read via SPI keeps drifting. Roll and Pitch angles are stable. Do you have any suggestion about this situation? Thank you. Ali Temel
View ArticleADIS16448 MTBF
Dear Analog staff, could you provide a MTBF rate prediction of the ADIS16448 device, based on the Parts Stress Analysis according tothe MIL-HDBK-217F? My application requires calculation for AUF...
View Articlehow to measure ADXL345 angle from g value
Hello, How to know axis g value to converter angle? 1 degree equal how many mg?I can't find any related angle and g converter document from website.Another question, may I set the both X and Y...
View ArticleADXL345 DATA READY interrupt and Signle&Double tap not working
Hello, I'm trying to read data form ADXL345 when it triggers data interrupt on int pin. During debbug sesion i see that ADXL345 do not let uC know that there is new data to read. It only let it know...
View ArticleC Code for ADXL375 interfacing on SPI
I have to interface ADXL375 with SPI on microcontroller.Is there any example code in C language.
View ArticleADIS16210 Delayed Read Question
What happens if I send the SPI command to read from one of the registers of the ADIS16210 (the Y Inclination Angle for example) and then delay before the next SPI command when the ADIS16210 actually...
View ArticleADMP504-installation of water pipeline
Hi,holding on which work is developing a project smart water networks, the objective of which is to monitor and identify possible losses through the installation of a sensor network within the duct.The...
View ArticleIssue at ADXL345
Hello, My customer use ADXL345 and they have some issues.They are using I2C interface to communicate with ADXL345. The issue is that they can get normal data of ADXL345 normally, but suddenly some time...
View ArticleADXL 206 higher G rating?
Are there any plans to make the ADXL 206 in any other G rating than +/-5G. its seems to be a great device, but only having one vibration range really limits the applications.
View ArticleADXL345 / ADXL346
What's the difference between these two, besides the power? Was this just a die revision, or was it complete redesign? Did the update rate issue with the 345 get fixed in the 346? Thanks, Tim
View ArticleConnecting an MSP430F5438 to an ADXL346 via SPI
Hi, I've been learning for the last while about SPI and how to implement it using the MSP430F5438 Microprocessor. I've came to the point where I've taken a SPI small demo application, and have changed...
View ArticleClik here to view.
ADIS16488A SPI Communication Troubles
Hey everybody, first post here, so let me know if I leave out some vital information. I work in a lab at a school, and we have been trying to read data from our ADIS16488A IMU with a Beaglebone Black's...
View ArticleADXL345 3 Wire and 4 Wire SPI Example Code
Attached are the ADXL345 3 wire and 4 wire SPI example code. It is verified on EVAL-ADXL345Z-M, the processor is ADUC7026, the development tool is KEIL C. I used GPIO to simulate the 3-Wire and 4-Wire...
View ArticleADXL345 in SPI getting wrong device ID and wrong output, working fine with I2C
Hi everyone,For my thesis project I'm using ADXL345 with nucleo-L053R8 board. Initially i connected in I2C and it is working fine. Later on i needed high datarates and switched to SPI. Unfortunately...
View ArticleWatermark interrupt problems with ADXL362
Hi, I am testing out a new reading scheme, to use interrupt based reading from FIFO instead of a poll method. I set:FILTER_CTL = 0x13FIFO_CTL = 0x0AFIFO_SAMPLES = 0x2CACT_INACT_CTL = 0x1FPOWER_CTL =...
View ArticleADXL001 noisy output
Dear community users, at the moment I try to set up a vibration monitoring system using the MEMS accelerometer ADXL001. To "check" the ADXL001 I have just made a small pcb. On this pcb I soldered the...
View ArticleADXL362 question
Hello, Please let me know your advice about beloq 3 questions of ADXL362.Our customer uses external clock and trigger.If possible, he would like to use higher data rate than 400Hz. Question1Datasheet...
View ArticleADXRS800 performance characteristiocs
Hello. My customer requested the Allan variance data.Do you have the data or similar data? Best regard.
View Article
