ADIS16375 Connection/Operational Requirements
I am experiencing strange behaviour with the ADIS16375 which i mounted on the ADIS16IMU1/PCBZ. When connecting the device to the microcontroller and power supply I am not able to get feedback. This is...
View ArticleADIS16334 old evaluation board
Hi I would like to use old ADIS16334 software.Please support me. I have ADISUSBZ and ADIS16334. (USB is typ-B)I installed new SDPDDrivers_2.exe and IMU_6DOF_3.Then it doesn't work. It should be an old...
View ArticleADIS16227 Accelerometer Equivalent
Its all good. I think we may be going to a different accel actually as this one is a little large for our product. We produce oil field bore hole surveying equipment and the OD of our current design...
View ArticleADIS16485 to Arduino Connection?
Hi guys, I am new to using the ADIS16485 and I have purchased the ADIS iSensor Evaluation Board to mount the sensor. I am trying to read the outputs from the sensor and I was wondering how to do this....
View ArticleInterface with EVAL-ADIS Evaluation System
Hi there, I've been doing the wireless transmission project, in which we hope we can utilize the evaluation board to display and capture data from 16488.The data from the imu including gyros and accls...
View ArticleEVAL-ADXL313Z Connector Part Number and Specifications
For the EVAL-ADXL313Z (ADXL313 eval board), there was a 10 pin connector included with the product.Since there is no datasheet for this evaluation board with a bill of materials, does anyone know the...
View ArticleADXL 312 FIFO function to improve resolution of inclination
Hi, I recently bought an ADXL 312 with evaluation boards inertial sensor evaluation board (ISEB). According to its datasheet, the resolution is 2.9 mg/LSB, which would enable resolution of inclination...
View ArticleHuge ADIS16480 gyroscope in-run bias
Hello. According to the datasheet, in-run bias does not exceed 6 degrees in hour,but I get approximatelly 240 degrees in hour. The following IMU's registers are configured:CONFIG = 0x00c0DEC_RATE...
View ArticleInterfacing ADIS16488 with Arduino
hey, I am using Arduino to read out data from ADIS16488 and print them serially on to the computer .I am new to using SPI and would like to get some assistance on how to go about with collecting data.I...
View ArticleADIS16480 Yaw angle drifts
Hi, I am trying to use ADIS16480 . Only yaw angle which is read via SPI keeps drifting. Roll and Pitch angles are stable. Do you have any suggestion about this situation? Thank you. Ali Temel
View ArticleHow to check if ADIS-16480 actually works ?
Hello, I have purchased an ADIS-16480 and tried to connect it to an Arduino board but I haven't been able to make it work. The programming of the Arduino should be fine, as my code is identical to...
View ArticleADIS16210 Dataready Latency
Hi Can you tell me how long it takes to make Dataready high after finish sampling the data? Regards,IN
View ArticleProblems with ADIS16265 EVAL Board ...
Hi everybody, I am just working on the implementation of a ADIS16265 Gyro into my roboter application and a have problems with the readings of the Evaluation board. The Board is sending sometimes...
View ArticleIMU Evaluation Software 1.7 DIO Configuration Reset?
I'm using the IMU Evaluation Software v1.7 with the EVAL-ADIS board and an ADIS16488 IMU. We've succesfully setup the EVAL-ADIS board to accept an external clock on DIO1 as well as output a Data Ready...
View ArticleNo Angle Outputs in the ADIS16480
I can not read any Euler's angles or velocity (DELTVEL)! I mannaged to read the PROD_ID,temperature, pressure and gyro reading well, however for Euler's angles and velocity I'm only getting zeros. When...
View ArticleHelp on chosing the correct IMU for mobile 3D scanner?
We have a 3d scanner for scanning industrial parts. Our scanner is a desktop solution. We want to make it mobile and it should be stay on the precise side. For this application we think we need IMU's...
View ArticleClik here to view.
adis 16364 gyro read problem
hello,i have an adis 16364 imu.when i write 0x3E00. i readC7 CF 9F FF 9F FF 9F FF 9F FF 8B E8 82 E1 82 EC 82 F0 83 27 8F FFC7 C7 9F FF 9F FF 9F FF 9F FF 8A 52 82 F8 82 E3 82 E7 83 1D 8F FFC7 CC 9F FF...
View Articlehow to get position and angle in ADIS16488A IMU Sensor
Hi all, I am using ADIS16488A IMU sensor for finding position and angles in my application. Actually in data sheet, they have mentioned Delta velocity and Delta angle will give one integration of...
View ArticleEVAL-ADIS/16485 and IMU Evaluation software
HiCan we use IMU evaluation software to evaluate ADIS16485 (using EVAL-ADIS) in Linux under Wine? Some relevant questions I found on the website are as follows: adisusb firmwareFAQ: Interface ADIS16364...
View ArticleHaving a problam w/ ADIS16488 SPI Communication.
Hi alli'm using the ADIS16488 and connected it with a TI DSP (delfino) through the SPI.while i'm running my code and sending addresses to the ADIS i'm getting right data (like PROD_ID etc..) but this...
View Article
