Help in design for a recoil recording device
I am currently testing different ways to record the difference in recoil of rifles with and without muzzle breaks. I've tried spring resistance on a sled on rails. And a weighted sled without the...
View ArticleADXL 312 FIFO function to improve resolution of inclination
Hi, I recently bought an ADXL 312 with evaluation boards inertial sensor evaluation board (ISEB). According to its datasheet, the resolution is 2.9 mg/LSB, which would enable resolution of inclination...
View ArticleADXL345 in SPI getting wrong device ID and wrong output, working fine with I2C
Hi everyone,For my thesis project I'm using ADXL345 with nucleo-L053R8 board. Initially i connected in I2C and it is working fine. Later on i needed high datarates and switched to SPI. Unfortunately...
View ArticleADXL213 REPLACEMENT
We are using the ADXL213AE from many years with very high results . Our main applications are : Platform leveling , cranes , aerial work platforms and many mobile applications . The inclinomeers that...
View ArticleNew Article on Optimizing MEMS Gyroscope Performance!
Just a quick reference to a newly released article: TITLE:Anticipating and Managing Critical Noise Sources in MEMS Gyroscopes ABSTRACT:When a MEMS inertial measurement unit (IMU) is operating as a...
View ArticleClik here to view.
ADXL362 self test output scale for different voltage
Hi, ADXL362 datasheet, table 22. If Vs=3.3V, self test output scale factor is? Thanks.
View Articlehow to get position and angle in ADIS16488A IMU Sensor
Hi all, I am using ADIS16488A IMU sensor for finding position and angles in my application. Actually in data sheet, they have mentioned Delta velocity and Delta angle will give one integration of...
View ArticleEvaluation board ADXL345Z query
Hi, We have procured ADXL345Z evaluation board and have few queries regarding that: 1. In static condition (i.e., at rest), is there still any reading (like an offset) from any of the three axes? 2....
View ArticleADXL345 and the MSP430F2013 I2C communication problem
I have set up an MSP430F2013 as the master and the ADXL345 as the slave. I am following the standard setup using the Device ID address of 0x1D. My scenario is thisGenerate a start on the I2C busSend...
View ArticleADXL213 REPLACEMENT
We are using the ADXL213AE from many years with very high results . Our main applications are : Platform leveling , cranes , aerial work platforms and many mobile applications . The inclinomeers that...
View ArticleGyroscope calibration tips
What type of information do you have on calibrating a MEMS gyroscope?
View ArticleHelp in design for a recoil recording device
I am currently testing different ways to record the difference in recoil of rifles with and without muzzle breaks. I've tried spring resistance on a sled on rails. And a weighted sled without the...
View ArticleEVAL-ADISZ + ADIS16488AMLZ. SDPERROR 4001: device not responding
Hi, I use EVAL-ADISZ + ADIS16488AMLZ for evaluation purposes. I've downloaded and installed a latest SDP drivers (EVAL-ADIS USB Driver Installation File (zip, 10790 kB)) and evaluation software (IMU...
View ArticleADXL345 in SPI getting wrong device ID and wrong output, working fine with I2C
Hi everyone,For my thesis project I'm using ADXL345 with nucleo-L053R8 board. Initially i connected in I2C and it is working fine. Later on i needed high datarates and switched to SPI. Unfortunately...
View ArticleWatermark interrupt problems with ADXL362
Hi, I am testing out a new reading scheme, to use interrupt based reading from FIFO instead of a poll method. I set:FILTER_CTL = 0x13FIFO_CTL = 0x0AFIFO_SAMPLES = 0x2CACT_INACT_CTL = 0x1FPOWER_CTL =...
View ArticleTemperature sensor of ADXL362
Hi I have a question about the datasheet of ADXL362 from my customer.The datasheet says that the standard deviation of bias in the temperature sensor is 290 LSB.It seems to be very large number as the...
View ArticleADXL213 REPLACEMENT
We are using the ADXL213AE from many years with very high results . Our main applications are : Platform leveling , cranes , aerial work platforms and many mobile applications . The inclinomeers that...
View Article[ADXL346] Z-Axis Offset Spec
Sir,This is AVNET FAE Kris,My customer use ADXL346 and there is one issue, Z-axis offset over spec, failed rate ~10%The failed parts's Z-axis offset almost locate at -250~-150mg As I know ADXL345...
View ArticleADIS16480 pitch and roll wander with magnetometer disabled
I have had four ADIS16480 modules in ice-deployed buoys in the central Arctic measuring wave-induced motion. I found that I was getting a lot of magnetic interference from a pulse-width modulated solar...
View Articleis there a Z axis accelerometer?
Hi, Is there a Z axis only accelerometer made by analog devices. For example if we use the ADXL203 you can get the X and Y axes acceleration. But if I want to measure the Z axis I have to have a PCB...
View Article
