ADIS16210
Dear supporterUsing the ADIS16210 controlled by an FPGA with the below pseudo code of VHDL driver:Spi_clk frequency = 500KHzCs = 1Clk = 1Upon request from software to read data from a register (address...
View ArticleReading the data from ADXL362 with MSP430G2230
Hi everyone. I will use spi accelerometer adxl362 for my project. My microcontroller is msp430g2230. Is there anyone who worked with project similar to mine? Could you post some code examples? Best...
View ArticleCN0303 - Logging multiple sensors
Hello - I need to synchronize data collection from two CN0303 eval boards and a 3rd sensor and record it in a data log. I realize that this is not the purpose of the evaluation software, but I'm...
View ArticleADXL344: Sampling rate
Hello, I have a question about the sampling rate of ADXL344. There is a description about the accuracy of internal RC oscillator of ADXL345 as follows./51039#51039 Is the clock generation of ADXL344...
View ArticleADIS16227 SPI communcations
Hello, I’m trying to use the ADIS16227 with a Raspberry Pi over the SPI interface. I’m communicating with the sensor using the linux spidev functions and sending commands using ioctl. I’m not getting...
View ArticleClik here to view.
What is the manufacturing spec for ADXL206HDZ?
What is the manufacturing spec for ADXL206HDZ?Is it possible to share that or does it comply to any industry standard such as MIL-PRF-38535K PERFORMANCE SPECIFICATION INTEGRATED CIRCUITS...
View ArticleThe use of ADXRS290 temperature sensor
Are there any reference materials on how using the data of the temperature sensor of ADXRS290, it can be calibrated in order to maximize accuracy, mainly long term stability. The data at this gyro’s...
View ArticleADIS16201 - Output data rate? - Alternatives with wide bandwidth?
Good afternoon everyone! Does anyone know what is the maximum Output Data Rate (ODR) of the sensor ADIS16201? Is it the same ODR when using the SPI port to access directly the digitylized measurement?...
View ArticleADXL362 rotate motion
Hi, Have any about ADXL362 rotate motion application notes, driver or others?Thank you!Kevin
View ArticleWhy DATAxx-registers are not updated in ADXL345?
I am ADXL345 is connected to ATmega 2560 with SPI (mode 3).I write data to the registers and read the recorded data from all registers. However, in the mode 2g (for example) 10-bit value data...
View ArticleUse of inexpensive MEMS accels as instrumentation-grade sensors
We use high quality tri-axial DC-accels ("instrumentation-grade") for in-vehicle (automotive industry) measurements of steering-response motions and vibrations. These accels cost approximately...
View ArticleWatermark interrupt problems with ADXL362
Hi, I am testing out a new reading scheme, to use interrupt based reading from FIFO instead of a poll method. I set:FILTER_CTL = 0x13FIFO_CTL = 0x0AFIFO_SAMPLES = 0x2CACT_INACT_CTL = 0x1FPOWER_CTL =...
View ArticleCan someone suggest some nice research topics for research proposal in...
i need to submit a research proposal for admission to research progrramme in Advanced MEMS and smart devices. Please give some helpThanks
View ArticleADIS16203 communication problems.....
I use is 16203 measuring inclinometer chip, DSP platform, a 16 bit data, in accordance with manual timing, phase = 1, polarity = 1, through the spi of tilt data read and din input sensor address,...
View ArticleADXRS290 - in-run bias stability and group delay
Hi, With regards to the ADXRS290, is there any empirical values for the following two parameters: in-run bias stability andgroup delay for the default configuration i.e. Low-Pass Filter: 480 Hz and...
View ArticleADIS16136 weird behaviour
Hi. I'm sampling the ADIS16136 gyroscope using an EVAL_ADIS with the following settings changed from the default ones: SMPL_PRD 000FhAVG_CNT 0006h; 16spsDEC_RATE 0007h; 10hz I'm seeing a weird...
View ArticleWhy DATAxx-registers are not updated in ADXL345?
I am ADXL345 is connected to ATmega 2560 with SPI (mode 3).I write data to the registers and read the recorded data from all registers. However, in the mode 2g (for example) 10-bit value data...
View ArticleProblem with FIFO read in Triggered mode with ADXL362
Hello, we are configuring the adxl362 with the following configuration:- THRES_ACT [codes] = 500- TIME_ACT = 4- THRES_INACT [codes] = 20- TIME_INACT = 200- FIFO_SAMPLES = 129- FIFO in triggered mode-...
View ArticleADXL 345 Development Board - Real Time Data
Cheers fellow tech freaks! I'm currently working on an ADXL 345 Development Board and i'm wondering if there's an interface or some way that i can get REAL TIME readings, like ADXL 345 evaluation kit....
View ArticleEnquiry for 9-axis IMU
Hi I have been involved in selecting 9-axis MEMS IMU’s to be placed in the drill head for some directional drilling applications. I’m interested in your products ADIS16488, ADIS16480, ADIS16407,...
View Article
