ADXL345 Bandwith
Hi, We are using the ADXL345. The datasheet don't include detailed information about filter and sensor electronic. The main question is if the sensor output are filtered or is the output of the acc...
View ArticleADXL001 noisy output
Dear community users, at the moment I try to set up a vibration monitoring system using the MEMS accelerometer ADXL001. To "check" the ADXL001 I have just made a small pcb. On this pcb I soldered the...
View ArticleEVAL-ADXL001
Hi, I have got an EVAL- ADXL001 board recently. Firstly, I have connect the board to dataphysics analyzes, but what I have got just like a sinusoidal signal and when I shake the board the signal did...
View ArticleADXL001-70z eval board noise on unfiltered XOUT
I see an 500kHz 40mVrms noise signal on the unfiltered XOUT. I am interested into frequencies up to 10kHz and I use the same opamp circuit like in CN0303 in our board. The 500kHz signal is going...
View Article[ADXL362] Changing ODR doesn't affect FIFO_WATER-MARK frequency
Good morning,I'm working on an university project, using MSP430 (msp430fr5969) with ADXL362 as gesture recognizer.I wrote my own libraries for the accelerometer communications, configurations and...
View ArticleADIS16488 SPI Extension
Is there anyway to get more distance between the ADIS16488 and the EVAL-ADIS? I am not sure if 12 inches will be enough.
View ArticleAccelerometer calibration tips
Are there any papers, articles or application notes on accelerometer calibration?
View ArticleGyro for high-acceleration environment - High G's
Hi, I'm working on a project that requires logging attitude data from high-powered rockets (amateur types, not military). I'll need to monitor all 3 axis. These rockets can see g-forces upwards of 20+...
View ArticleADIS16480 and Evaluation Board Questions
(Background:) I (or more specifically my team) recently bought the ADIS16480 and the corresponding evaluation board for use with the BeagleBone Black. This board boots from a microSD card with an...
View ArticleADXL362 - SPI communication issues
Hi, I'm trying to make an ADXL362 talk to a microcontroller (the nRF51822-Eval borad). I am trying to read the 0x00 register, therefore I send 0x0B and then 0x00. As you can see in the attached,...
View ArticleExternal clock with EVAL-ADIS and ADIS16485
I would like to use an external trigger with the EVAL-ADIS, the ADIS16485, and IMU Eval Software. My Setup:I am using the EVAL-ADIS board and the ADIS16485 IMU.It is hooked up via USB and the jumper...
View Articlehaving problem in understanding my ADISa6448 output
hi all im using ADIS16448 with pic32. im having a problem and i wish if you can help me wihh. im reading out my ADIS, im receiving correct data for the identification register. but im facing problem in...
View ArticleADXL362 Dev Board Data Logger Souce Code/File System Questions
Hi, I have been playing around with my ADXL362 Datalogger & Dev board and I'd like to make some modifications to the demo code, but I can't find the source files for the demo. Is the source code...
View ArticleSD-Card in ADXL362 Development Board / Datalogger
Hi, I would like to use a second SD card for the Dev Board. Unfortunately the new cards don´t work. The GUI always gives an error, so I assume it is a problem of formatting the card. Also the included...
View ArticleAccelero probleme with ADIS16448
Hello every body I have some problemes with our ADIS16448.We connect it to a spartan6 the readout is donne with burst mode every 100 Hz. We are using a clock a 100 Mhz and every thing seems...
View ArticleSPI reading issue in ADIS16480
Hi, I am using TIVA LM4f232 eval kit to read sensor values from ADIS16480.While reading through SPI I am able to get correct data only when I am sending twice the read command. After initialization,...
View ArticleADXL001-70z eval board noise on unfiltered XOUT
I see an 500kHz 40mVrms noise signal on the unfiltered XOUT. I am interested into frequencies up to 10kHz and I use the same opamp circuit like in CN0303 in our board. The 500kHz signal is going...
View ArticleMEMS accelerometer: Advice before purchase.
Hey,Need Help in purchasing mems accelerometer. Measurement requirements:1. Gauge used to measure vibration.2. Bandwidth: At least 10 khz.3. Acceleration Range: 50 g4. Dimensions: Not larger than 5x5x5...
View ArticleADIS16480/EVAL-ADIS Source Code Libraries
I am investigating the use of the EVAL-ADIS in prototype test system for our evaluation of the ADIS16480. Does the EVAL0-ADIS come with any source code libraries? If so, where can I find them?
View ArticleHow to make IMU sensors insusceptible to surrounding electronics?
Hi, I am using two IMU sensors to perform the same tests and they are: ADIS16360 and ADIS16362. I attached my IMU sensor on a robot arm to take some data and the gyroscope measurements were always out...
View Article
