Reading the data from ADXL362 with MSP430G2230
Hi everyone. I will use spi accelerometer adxl362 for my project. My microcontroller is msp430g2230. Is there anyone who worked with project similar to mine? Could you post some code examples? Best...
View ArticleWhat is the difference between ADXL362 and ADXL363
What is the difference between ADXL362 and ADXL363?
View ArticleADIS16203 software error
Hi I am trying to evaluate the ADIS16203 with the ADISUSBZ board, my software seems to install fine (both of an XP-32 bit and Windows 7 32 bit machine). When I go to run the program I get a windows...
View ArticleAccelerometer?
Does ADI have anything comparable? http://www.meas-spec.com/downloads/832.pdfhttp://www.meas-spec.com/downloads/834.pdf
View ArticleMicroSD card issue EVAL-ADXL362Z-DB
Hello,The customer who has been using EVAL-ADXL362Z-DB have an issue about micro SDCARD accesss via EVAL-ADXL362Z-DB.The MicroSD card that include EVAL cannot be written settings data even displayed...
View ArticleInertial Sensor with inclination, acceleration, and Gyro Sensing
Hi All, My customer is considering inertial sensor device for his new design.Specification is as next;Inclination/accelerator: 0.1 deg inclination resolution, 0.2 deg accuracy (including initial offset...
View ArticleADXL345 output variation vs sample rate?
The output varies across different sample rates. No filter rates or any other parameters are changed between the two data sets and INT_1 is used to signal data ready. Below are 8 sequential reads from...
View Articleadxl362: trouble getting GUI for eval kit
Hi, I just got an eval kit for the '362 (EVAL-ADXL362Z-MLP), and after installing USB drivers and connecting the main board I reached the instruction, in user's manual, calling for installation of the...
View ArticleADXRS290 Analog Mode with Single Supply OPAMP
Hi to all!Can you suggest me a circuit (like the figure 28 on the ADXRS290 datasheet, page 12) to demodulate PDM outputs but with a +5V single supply OPAMP? Thank you for your collaboration. Graziano
View ArticleADIS16209 Accuracy Problems and Assembly issues
Hi, we have a program in which there is an ADIS16209 as the mail tilt sensor.we have tested several units via the evaluation board and they performed to spec.we had made a PCB design which includes the...
View Articleadis16480 euler angle drift
Hi there,I got a new adis16480amlz and the corresponding eval-adis. I have two doubts,1. the datasheet of adis16480 says, pin 10, 11, 12, 23 should connect to +3.3v. but the figure below implies JP2 is...
View ArticleUnderstand ADXL345 output
Hi Folks,I am newbie in MEMS domain. In order to learn MEMS motion sensors (for few undecided projects) I borrowed an RL78/ADXL345 board from friend and started playing with it. I am attempting to...
View ArticleReading the data from ADXL362 with MSP430G2230
Hi everyone. I will use spi accelerometer adxl362 for my project. My microcontroller is msp430g2230. Is there anyone who worked with project similar to mine? Could you post some code examples? Best...
View ArticleADIS 16480 Question
hi, I have a ADIS 16480 evaluation board and I have some questions about that as follows:1. what is the output unit for the gyroscope and accelerometer, (degree/s and g)?2. X_GYRO_OUT is the angular...
View ArticleInertial Sensor with inclination, acceleration, and Gyro Sensing
Hi All, My customer is considering inertial sensor device for his new design.Specification is as next;Inclination/accelerator: 0.1 deg inclination resolution, 0.2 deg accuracy (including initial offset...
View ArticleAD9625 modes of operation
Hi, A customer of mine is seeking to reduce the number of JESD204B lanes in which he needs to interface his FPGA to the AD9625. The reason is due to the pricing of the FPGA. If he can interface to the...
View ArticleADXL375 saturating at 25g
I am noticing that the ADXL375 device in my design is saturating at 25g when I set the bandwidth at 3200 hz. Same applies to lower data rates as well.I am reading the values in bypass mode.Any help is...
View ArticleEVAL-ADXL362Z-DB real-time evaluation sysytem trouble
I am using EVAL-ADXL362Z-DB.I am in trouble not to display the results of X/Y/Z axis on the GUI.--Condition--GUI : ADXL362 EVB BUI V1.1.viFirmware : ADXL362DB_MultiDemo_Firmware (HEX)SW2 :...
View ArticleADXL312W temperature coefficient
Hi, I have a customer using a ADXL312W. According to the datasheet, the typical 0g offset temperature coefficient is +-0.8mg/C for x/y. The typical characteristics on page 7 do not match this. The...
View ArticleADXL345 output variation vs sample rate?
The output varies across different sample rates. No filter rates or any other parameters are changed between the two data sets and INT_1 is used to signal data ready. Below are 8 sequential reads from...
View Article
