ADIS16375 TIME_YM_OUT register
When I use the ADIS16375, I can set the TIME_MS_OUT register successfully, but I can’t set the TIME_YM_OUT register.
View ArticleArduino Example using the ADIS16448
Hey everyone! I just finished up a project using the ADIS16448 and wrote up a library which was easily adapted to the Arduino. I'm posting the link to the code so that others might be able to use it as...
View ArticleADXL362 Fifo Trigger Mode
Hi, I have a quick question. How would I find out when fifo got enough new data after a Trigger FIFO event occurred? I would like to sample 2s prior and after an threshold interrupt. My...
View Articleaccelerometer vibration reduction
Hallo, welche Typenbezeichnung haben die Beschleunigungssensoren, welche nicht auf Vibrationen (Schwingungen) reagieren (keinen Signalausschlag ausgeben)? Beste GrüßeMario Hello, I am looking for...
View ArticleAdxl312 doesn't ack below 2.4V
Hi, Everything is mentioned in title! Above 2.4V, everything is working fine. Below, I don't get any ack from the sensor. MCU is powered directly while ADXL and I2C bus are powered through and analog...
View ArticleADXL362 FIFO triggered mode not working
Hi, I'm using ADXL362 in my application. I want to use the triggered mode on activity interrupt. If i well understood, the fifo will fill up, everytime when there is activity. But even there is no...
View ArticleClik here to view.
ADIS16210 - Inconsistent Interrupt Timing
Hi, I am integrating an Analog ADIS16210 accelerometer with an FTDI Vinculum II processor. I can successfully communicate across the SPI interface. The accelerometer is interfaced across a PCBZ...
View ArticleClik here to view.
ADIS16229 transmission time and power consumption
Hi Sir, one of my customer is evaluating the total power consumption but there still are some confusion needs help to clarify 1. the recording time: is tR already including the transmitting...
View ArticlePicking IMUs
Hi, I'm currently working on adding an IMU to our product that can accurately output the relative position and orientation. Our product will be used under room temperature. We need the gyro has...
View ArticleADXL362 not functional?
Hi All,After setting up my sparkfun breakboard-mounted ADXL362, and having seen g's about 1.3 while still, I decided to run the self-test on it. I am not too experienced with programming these babies,...
View ArticleInclination accuracy ADIS16210
Hello all, In an application I'm using the ADIS16210 as an inclinometer. The accuracy is good. The noise is approx. 0.02 degrees (3 to 4 datapoints) which comes close to what I need for the...
View ArticleADXL213 possible noise sources?
I'm using an ADXL213 in an existing design, and I think I'm seeing more noise than I had expected. The ADXL213 is set up with Cx and Cy both 1uF, and Rset is 5.1M. Cdc is 0.1uF. I'm using a MCF54415...
View ArticleADXRS290 Analog Mode with Single Supply OPAMP
Hi to all!Can you suggest me a circuit (like the figure 28 on the ADXRS290 datasheet, page 12) to demodulate PDM outputs but with a +5V single supply OPAMP? Thank you for your collaboration. Graziano
View ArticleHow to set ADIS16228 in manual FFT, please...
Hello all My name is Cristian Dumitrescu and I am from Romania, working at S.C. AEROFINA S.A..We've recently puchased a ADIS16228 for evaluation/testing purposes. The sensor is controlled by a...
View ArticleClik here to view.
ADXL375 Output Data Rate vs. Current Consumption
Some may have noticed what looks like an interesting anomaly in the data sheet for the ADXL375. On p. 9 of the data sheet, Fig. 18 shows Output Data Rate (ODR) vs. Current Consumption. At an ODR of...
View ArticleICD says bits are "not used" but some are set High??
I recently observed something unusual on an ADIS16365. When the master system read the MSC_CTRL register, several of the bits that are marked as "not used" in the ICD (datasheet) returned "1"....
View ArticleClik here to view.
ADXL362 X,Y,Z 8-bit result interpretation
Hi, I am trying to make sense of the results I had with the ADXL362. The accelerometer is built on a platform that we can access via Bluetooth. I can send commands from a phone to read X, Y, Z...
View ArticleInterpreting ADXL325 Data Results
Hello: I'm hoping someone could set me on the path of understanding on the best way to interpret the accelerometer data I've gathered. I used the evaluation board EVAL-ADXL325Z to log data. For the...
View ArticleClik here to view.
High Accuracy High Precision Gyro
Hi, 1. I have a huge metal block which rotates clockwise as well as anticlockwise. The speed of movement is not so high. However there is a huge shock which passes through the block sometimes. 2....
View ArticleInterfacing the ADXL345 with MSP430F5438A per 4 wire SPI
Hi! I am trying to connect the ADXL345 to my MSP430F5438A per 4 wire SPI. My first step was to receive the correct ID of the ADXL345 and to get in the next step the right informations of the different...
View Article
