AD22293ZA vs. AD22293Z
I want to order a small number of AD22293 +- 5g. In the datasheet, it is named as AD22293ZA. When I go to inventory, there is the AD22293ZA which is not available and the AD22293Z. What is the...
View ArticleADIS16227 SPI communcations
Hello, I’m trying to use the ADIS16227 with a Raspberry Pi over the SPI interface. I’m communicating with the sensor using the linux spidev functions and sending commands using ioctl. I’m not getting...
View Articleadxl345 sequence of data reading
In multi byte data transfers does the adxl345 automatically output the bytes sequencially or does each byte have to be requested by the host? Also is there a way to do constant repeative readings for...
View ArticleADXL362 interrupts
I am using the ADXL362 with an ATTINY85 I want to run the script for a certain period then a) put the ADXL362 into wakeup mode and next b) put the ATTINY85 into power down sleep mode.I would then like...
View ArticleADIS16480 pitch and roll wander with magnetometer disabled
I have had four ADIS16480 modules in ice-deployed buoys in the central Arctic measuring wave-induced motion. I found that I was getting a lot of magnetic interference from a pulse-width modulated solar...
View Articlehow to measure Vibration using ADXL213
hi,can any body tell me how to calculate vibration using ADXL213ADXL213 output is in gg= (T1/T2– 0.5)/30% then how this convert in to viration ,is there any formule for tha conversion.
View ArticleSome ADXL362 spi-data issues
Hi, I've been using ADXL362 in my application for a year or so (with tens of samples) and recently i was facing 2 major issues:1. Some of the samples, suddenly sending constant 3D measurements - even...
View ArticleADIS16480 Yaw angle drifts
Hi, I am trying to use ADIS16480 . Only yaw angle which is read via SPI keeps drifting. Roll and Pitch angles are stable. Do you have any suggestion about this situation? Thank you. Ali Temel
View ArticleInterface with EVAL-ADIS Evaluation System
Hi there, I've been doing the wireless transmission project, in which we hope we can utilize the evaluation board to display and capture data from 16488.The data from the imu including gyros and accls...
View ArticleAdxl312 doesn't ack below 2.4V
Hi, Everything is mentioned in title! Above 2.4V, everything is working fine. Below, I don't get any ack from the sensor. MCU is powered directly while ADXL and I2C bus are powered through and analog...
View ArticleADXL362 Identify the Motion Axis
Hi, As I understand, there is no direct way to identify the axis which triggered the motion detection (X, Y or Z). Am I right? Should I implement it by reading the samples after the trigger? Is there...
View ArticleADIS16480 and Evaluation Board Questions
(Background:) I (or more specifically my team) recently bought the ADIS16480 and the corresponding evaluation board for use with the BeagleBone Black. This board boots from a microSD card with an...
View ArticleADIS16228 FFT avg
Am I correct that table 19 and table 20 on page 16 of the Data Sheet rev B is not adding up?Default = 0x0108 in Table 19Default = 0x0101 in Table 20are they not the same?In the previous text...
View ArticleHow to set ADIS16228 in manual FFT, please...
Hello all My name is Cristian Dumitrescu and I am from Romania, working at S.C. AEROFINA S.A..We've recently puchased a ADIS16228 for evaluation/testing purposes. The sensor is controlled by a...
View ArticleADIS16227 continual realtime time-domain sample capture
Hi all, My project specification requires 3-axial acceleration capture +- 70g at a rate >= 3200 samples-per-second. Unfortunately I have discovered too late that ADIS16227 is not designed for...
View ArticleClik here to view.
Queries on ADIS16405 & ADIS16448 temperature sensor reading
Hi, I am working on a small satellite project which uses both of the MEMS IMU mentioned in the title in our hardware. I noticed that there is an huge difference in the temperature reading (around 11...
View ArticleCalibrating ADXL375
Hi, I have a ADXL375 accelerometer evaluation board which I've connected to an atmel board. I'm now able to configure the accelerometer as I want and read the acceleration. I've defined the Bandwidth =...
View ArticleQuestions for your Spec of ADXRS290
Dear Sir/Madam, I have a couple of questions here. Question-1)What is the cross axis sensitivity max ?It cannot show table-1 in your datasheet I know.How should we fix it for our design? Question-2)As...
View ArticleADXL377 maximum shock rating
Hi All, One of my customer sent me a following question.Absolute Maximum Ratings of ADXL377 data sheet says that maximum acceleration is 10,000g,He is comparing STM H3LIS200DL accelerometer, and its...
View ArticleClik here to view.
ADXL375 saturation at 25G, and DATA format register seems like stucked
Hi, I got some problem while using ADXL 375. It doesn't give me 200G how hard I trys....And as the graph, it saturates at 25G. I changed 0x31 Register, but it didn't work. Any suggestions? Thank...
View Article
