ADIS16227 SPI communcations
Hello, I’m trying to use the ADIS16227 with a Raspberry Pi over the SPI interface. I’m communicating with the sensor using the linux spidev functions and sending commands using ioctl. I’m not getting...
View ArticleADXL345 output variation vs sample rate?
The output varies across different sample rates. No filter rates or any other parameters are changed between the two data sets and INT_1 is used to signal data ready. Below are 8 sequential reads from...
View Articlelow power 6 axis sensor from ADI
I am looking for low power 6 axis sensor for my smart watch project. Sadly all the IMUs from ADI consume much higher power than other similar products. For...
View ArticleADIS16209 power supply considerations
accordingly to datasheet information the VDD must ramp up within 100us.If this could not be met, is it possible to activate the RESET input until VDD is up and stable?
View ArticleADXL362 Identify the Motion Axis
Hi, As I understand, there is no direct way to identify the axis which triggered the motion detection (X, Y or Z). Am I right? Should I implement it by reading the samples after the trigger? Is there...
View ArticleADIS16488A Data Ready
I had to lay off the IMU for a while to work on other project, but good news is that I have the ADIS16488A working just about 100%. I am using a Raspberry Pi to communicate with the IMU and have no...
View ArticleADXL377 maximum shock rating
Hi All, One of my customer sent me a following question.Absolute Maximum Ratings of ADXL377 data sheet says that maximum acceleration is 10,000g,He is comparing STM H3LIS200DL accelerometer, and its...
View ArticleADIS16228 Eval Kit
HI Mark, Got it. Could you send me a quote for the ADIS16228 and the Eval Kit? Is there a request form I can fill out somewhere? Thanks. Regards,Varun
View ArticleADIS 16229 Eval Kit
Hi, This question is in regards to the Evaluation Kit provided by analog Devices EVAL-ADIS.I wished to purchase the ADIS 16229 and the EVAL kit- just wanted to get an idea as to how the EVal kit works....
View ArticleADIS16227 SPI communcations
Hello, I’m trying to use the ADIS16227 with a Raspberry Pi over the SPI interface. I’m communicating with the sensor using the linux spidev functions and sending commands using ioctl. I’m not getting...
View ArticleADIS16375 Connection/Operational Requirements
I am experiencing strange behaviour with the ADIS16375 which i mounted on the ADIS16IMU1/PCBZ. When connecting the device to the microcontroller and power supply I am not able to get feedback. This is...
View ArticleClik here to view.
ADIS16488A SPI Communication Troubles
Hey everybody, first post here, so let me know if I leave out some vital information. I work in a lab at a school, and we have been trying to read data from our ADIS16488A IMU with a Beaglebone Black's...
View ArticleADXL345 output variation vs sample rate?
The output varies across different sample rates. No filter rates or any other parameters are changed between the two data sets and INT_1 is used to signal data ready. Below are 8 sequential reads from...
View ArticleCalibrating ADXL375
Hi, I have a ADXL375 accelerometer evaluation board which I've connected to an atmel board. I'm now able to configure the accelerometer as I want and read the acceleration. I've defined the Bandwidth =...
View ArticleAcceleration/Force conversion of ADXL326 and ADXL377 Accelerometer
I am a PhD student in Tokyo Institute of Technology. My research relates to triboluminescence properties observed via dropping test. The challenging task is how to determine a magnitude of impact...
View ArticleADIS16209 power supply considerations
accordingly to datasheet information the VDD must ramp up within 100us.If this could not be met, is it possible to activate the RESET input until VDD is up and stable?
View ArticleQuestions for your Spec of ADXRS290
Dear Sir/Madam, I have a couple of questions here. Question-1)What is the cross axis sensitivity max ?It cannot show table-1 in your datasheet I know.How should we fix it for our design? Question-2)As...
View Articleadxrs642 scalefactor
hii have an adxrs642 gyro.i want to increase output of this gyro from 250 deg/sec to 1200 deg/sec. how can i do it?
View ArticleADXL375 not working with Windows 8/8.1
We can't get the ADXL375 eval board to work with Win 8, apparently no drivers built. Has anyone else encountered this, and if so, is there a workaround. Troy
View ArticleADXL362 Identify the Motion Axis
Hi, As I understand, there is no direct way to identify the axis which triggered the motion detection (X, Y or Z). Am I right? Should I implement it by reading the samples after the trigger? Is there...
View Article
